Trenz Electronic GmbH
TE0706 - Carrierboard for Trenz Electronic Modules with 4 x 5 cm Form Factor (TE0706-04-A)
Simple carrier board for Trenz Electronic 4 x 5 modules. Mainly for the TE0820/TE0720/TE0715 modules
Numero di variazione (MEPA): VAR-827003062
Codice produttore: TE0706-04-A
Codice doganale:
Articolo situato in e spedito da: Riedlingen, Germania
The predecessor of this article is TE0706-04. All changes are in the Product Change Notification (PCN).
The TE0706 carrier board provides functionalities for testing, evaluation and development purposes of Trenz Electronic 4 x 5 cm SoMs. It is mainly for the use with TE0820, TE0720 and TE0715 modules. The carrier board is equipped with various components and connectors for different configuration setups and needs. The interfaces of the SoMs functional units and PL I/O-banks are connected via board-to-board connectors to the carrier board's components and connectors for easy user access.
See page "4 x 5 cm carriers" to get information about the SoMs supported by the TE0706 carrier board.
Key Features
- 3 x Samtec LSHM series board to board connectors
- VG96 connector (mounting holes and solder pads) and 50-pin IDC male connector socket for access to PL I/O-bank pins
- USB2.0 type A connector, or optionally Micro USB 2.0 connector
- 1 x RJ45 GbE MagJack, connected via MDI to B2B connector
- 1 x GbE PHY, providing Ethernet interface in conjunction with RJ45 GbE MagJack
- 4A High-Efficiency Power SoC DC-DC Step-Down Converter for 3.3V power supply
- XMOD JTAG-/UART-header JX1
- 1 x TE0790, XMOD FTDI JTAG Adapter - AMD/Xilinx compatible (pre-assembled)
- Micro SD card socket
- SDIO port expander with voltage-level translation and jumper for selection of SDIO voltage on SoM side
- DIP-switches S1 to set SoM's control signals
- 1 x user-push button, by default configured as system reset button
- 3 x VCCIO selection jumper to set SoM's PL I/O-bank voltages
- 5V power supply barrel jack
- Size: 64.5 x 100 mm
Scope of Delivery
- 1 x TE0706-04-A carrier board for Trenz Electronic modules with a form factor 4 x 5 cm
- 1 x TE0790-04, XMOD FTDI JTAG Adapter - AMD compatible (pre-assembled)
Note: VG96 Connector vertical (article 21545), Harting DIN41612 (female) is not included in the scope of delivery, but can be purchased as an accessory in the shop. (https://wiki.trenz-electronic.de/display/PD/PCN-20231106+TE0706-03+BOM+Change)
Info: M2.5x8 mm screws and M2.5 galvanized nuts are required for mounting the VG96 connector.
Additional Information
- Manufacturer's article number: TE0706-04-A
- Trenz Electronic TE0706 Wiki
- Support Forum
All modules produced by Trenz Electronic are developed and manufactured in Germany.
| ID articolo | 102610 |
| Condizione | |
| ID della variazione | 3890 |
| Modello | TE0706-04-A |
| Produttore | Trenz Electronic GmbH |
| Paese di produzione | |
| Contenuto | 1 undefined |
| Peso | 118 g |
| Peso netto | 118 g |
